Fire Alarm Control Panels
F4AUXRLYV2
Provides additional (auxiliary) fire and fault (defect) relays for an F4 conventional fire alarm control panel
Networking
Software Applications
FAAST PipeIQ v3.0.0
A Windows®-based application for designing and specifying FAAST aspirating smoke detection systems
Extinguishing Agent Release Systems
Equipment Cabinets
Mimics, Repeaters & Interfaces
F100A LCD Mini Mimics
LCD mini-mimic remote display for Pertronic F100A & F120A analogue addressable fire alarm control panels
L485LAC
Controller for driving multiple LEDs, relays, or open collector outputs from a Pertronic fire alarm control panel's RS-485 bus
F4-RMAX
Interface for connecting a remote LED mimic to an F4 fire alarm control panel. With auxiliary fire and auxiliary fault (defect) relays
LED Display Boards
LED display boards for Pertronic fire alarm systems including F100, F120, and F16e
SGD7 Signal Gen
Signal generating device which provides a transmission interface between fire alarm systems and LTX series alarm transmitters
F100AMME
Escutcheon plate for flush-mounting the Pertronic LCD Mini-Mimic
CLC-MON-N9P
Flexible RS-232 extension lead with DB9 male and DB9 female connectors and straight-through connection
Transmitters
SGD7 Signal Gen
Signal generating device which provides a transmission interface between fire alarm systems and LTX series alarm transmitters
Accessories
F120TOF220KIT
Kit for upgrading an F120A system to an F220, including masterboard, keyboard+display, and brackets (excludes outer door)
CPTST Weatherproof
A tough, transparent, weatherproof polycarbonate shield and frame that fits over a manual call point
CPTST series
A tough, transparent, polycarbonate shield and frame that fits over a manual call point. Fitted with warning sounder
CPTSTPRHTR
A tough, transparent, polycarbonate shield and frame that fits over a manual call point, with built-in 230 Vac heater
F4AUXRLYV2
Provides additional (auxiliary) fire and fault (defect) relays for an F4 conventional fire alarm control panel
CPPFPL
Fascia panel for flush-mounting Pertronic Manual Call Points in place of large old manual call points (break-glass alarms)
SBB-L
Surface-mounting back boxes for L Series alarm (alerting) devices. Available in wall-mount and ceiling-mount variants.
MCP Windows
Replacement windows for Manual Call Points, including Snapglaze and Break-Glass types
EXTSPKRHOUS
Vandal-resistant enclosure for horn speakers. Power-coated zintec.
F4-RMAX
Interface for connecting a remote LED mimic to an F4 fire alarm control panel. With auxiliary fire and auxiliary fault (defect) relays
RLY24V
Auxiliary relay board with two form C (changeover) contacts rated 4 Amps, 30 Vdc (resistive). 24 Volt (nominal) coil
CP500
Handheld Programmer for Analogue Addressable Weatherproof Detectors
CLC-MON-N9P
Flexible RS-232 extension lead with DB9 male and DB9 female connectors and straight-through connection
F-SEN-SSE
Replacement smoke sensor for FAAST LT-200 series aspirating smoke detectors
F100ZIPB
Eight-way opto-isolated input board for the Pertronic analogue addressable loop responder and multi-function loop responder
Fire Door Holders
Floor-mount or wall-mount electromagnetic door holders for fire doors
FDHWM38-24V
Wall-mount electromagnetic door holder for fire doors
FDHWM65-24V
Wall-mount electromagnetic door holder for fire doors
MOXA-TCF-142 Series
MOXA serial to fire-optic converters for RS-232 and RS-485 circuits. Transmit up to 40 km over single-mode fibre-optic cable
Tools and Test Equipment
OSID Laser Tool
This tool clips into the eyeball on OSI/OSID beam smoke detectors. It produces a red laser beam showing the detector beam's target
CP500
Handheld Programmer for Analogue Addressable Weatherproof Detectors
Sensitivity Reader
The SENS-RDR is a tool to measure the sensitivity of System Sensor model 2151BPI conventional photo-electronic smoke detectors only.
